ReliaMed Lower Back Pain Relief System Delivers targeted relief for lower back pain. Prescription-strength TENS device allows for a wide range of adjustments. Helps reduce lower back pain due to muscle strain from exercises and household work or activities. Fits comfortably under clothes, Highly portable. Compliance meter allows physician or therapist to monitor patient's actual usage time in hours. Includes ReliaMed(r) Three-Mode Digital TENS Unit, 9-volt battery, one-size-fits-most adjustable neoprene belt with lead wire storage, four double-sided electrodes, two sets of lead wires, for snap adapters (for lead wire attachment) and instruction manual. Latex-free.

Back Belt w/TENS Price $ 154.95

Electro-Therapy Products

TENS, EMS, Micro-Current, Electro-Acupuncture and Point Locators

 <<BACK   Page  1  2  3  4    NEXT>>
Click on picture to enlarge (use browser back button to return)

ReliaMed TENS and EMS Combo Unit Features slide cover over controls. Timer features 30- and 60-minute fixed programs; and continuous. Dual, isolated channels. Pulseintensity is adjustable 0 - 80 mA peak into 500 ohm lead each channel, constant current. 2 Hz - 120 Hz adjsutable pulse rate. 40 us - 260 us adjustable pulse width for TENS; 250 us fixed pulse width for EMS. 0 - 110 volts. Five modes include burst, continuous, modulation, synchronous and alternation. In burst mode, TENS unit features 2 bursts/second, 9 pulses/burst, 100 Hz and adjustable width. In continuous and modulation modes, pulse rate, pulse width and amplitude are fully adjustable. For EMS, in synchronous and alternation modes, on ramp is adjustable 1 - 8 seconds, and cycle on/off times are adjustable 1 - 30 seconds. 95 mm x 61.5 mm x 26 mm. Includes two lead wires, one pack (4) electrodes, 9-volt battery, carrying case and manual. Digital TENS and EMS Combo Unit Cap and slide cover protect against accidental setting changes. Features seven modes: burst, continuous, modulation, strength-duration and rate modulation, strength duration and width modulation, synchronous; and alternation. Timer features 15, 30 and 60-minute programs of fixed duration, and one continuous. 1 Hz - 160 Hz (adjustable), 1 Hz/step (1 Hz - 20 Hz), 5 Hz/step (20 Hz - 160 Hz) pulse rate. 50 - 260 adjustable pulse width for TENS, and 250 fixed pulse width for EMS. By changing mode, output resets to zero, then ramps up to its original setting intensity to protect user from a sudden surge. Patient compliance counter shows treatment time in hours. Patient lock system prevents user from changing fixed parameters set by physician or licensed practitioner. For TENS, LCD panel displays modes, pulse rate, pulse width, timer and channels. For EMS, LCD panel displays modes, pulse rate, ON time, OFF time, timer and channels.Dual Channel Microcurrent Unit Modified, square, DC, biphasic waveform with pulses of 0.3 Hz, 8 Hz and 80 Hz, changing polarity at intervals of three seconds. Timer can be set of 20 and 40 minute treatment periods; or continuous. Includes stimulator; lead wires; one pack (4) electrodes; 9-volt battery; hard-sided, protective, plastic case; and instruction booklet.

Digital TENS TS-1211 This is a portable dual channel TENS with a 0.8” x 1.6” digital display screen. This unit features 5 stimulation modes, including strength, duration and bi-pulse. The memory feature retains last setting for quick and easy set-up. Includes self-adhesive electrodes (1.5” x 1.5”) with wires, carrying case, belt clip, 9-volt battery and instructions. Features 2 independent intensity output channels and a timer for 5 to 90 minute treatments. Adjustable frequency 2 – 150 Hz. Digital EMS TS-1311 This is a portable dual channel EMS with a 0.8” x 1.6” digital display screen. The memory feature retains last setting for quick and easy set-up. Includes self-adhesive electrodes (1.5” x 1.5”) with wires, carrying case, belt clip, 9-volt battery and instructions. Features 2 independent intensity output channels and a timer for 5 to 90 minute treatments. Adjustable frequency 2 – 120 Hz., 3 pulse modes, constant, synchronous and alternate. Adjustable cycle on, cycle off and ramp time. Micro-850 This unit is 2-channel micro-current with 3 fixed frequency settings and an adjustable timer. Includes self-adhesive electrodes (1.5” x 1.5”) with wires, carrying case, belt clip, 9-volt battery and instructions. Features 2 independent intensity output channels. Fixed frequencies of 0.3, 8, and 80 Hz.

EMS 400 This is a portable, handheld, dual channel EMS. Includes self-adhesive electrodes (2” x 2”) with wires, carrying case, belt clip, 9-volt battery and instructions. Features 2 independent intensity output channels. Adjustable frequency 2 – 120 Hz., 2 pulse modes, constant and cycle. Adjustable cycle on, cycle off and ramp time. ITO ES-130 Introducing the new ITO ES-130, this model replaces the popular IC-1107+. This new model is designed and calibrated to meet all essential safety and regulatory industry standards. With its fresh new look, the ES-130 is a compact, lightweight, sturdy, palmsize, high quality Japanese electro-therapy device. Featuring a High/Low switch on the back of the unit, the switch is toggled to Low to facilitate use with needles or to High for MEA electro-therapy. It offers three independently controlled output channels with adjustable frequency indicated by a flashing light. The waveform is a unique biphasic pulse which has been designed to minimize electrolysis damage to the needle. The pocket portable ES-130 is the smallest and smartest looking professional electro-therapy unit in the world, for use in or out of the office. This unit is not equipped with a point locator. Accessories include 3 sets of new CE wire leads with rectangular CE jack, carrying case, and instructions. Does not include battery. Note: When using 9-volt Duracell Batteries with the ES-130, a thin shim (or paper) must be placed at the bottom of the battery to make proper contact (Duracell are shorter in length). Also, in order to use the built-in battery check (located on the back side of unit), power must be turned on.AWQ-104L This is the latest version of a multi-purpose electro-acupuncture series from China. This unit features 4 independently controlled output channels and a large 0.5” x 0.9” LCD digital meter which displays both frequency and point location. Location is also indicated by light and sound. 3 adjustable pulse modes and a hi/low voltage switch. Accessories include 5” long pen shaped search/treatment probe with hand ground pole and wire, 4 sets of alligator clip wires, sturdy carrying case, 9-volt battery and instructions.

Acu Machine 6CH The new and improved Acu Machine features an indicator for sound and luminescent state, a timing switch, a power voltmeter and an operating output protection. The output pulse waves of the machine are in low voltage and low frequency range. Five types of pulse waves to choose from: Continuous wave, Dense-disperse wave, Intermittent wave, Ripple wave and Respiration wave. Four kinds of wave combinations can be used at the same time, separately or in unison. Unit comes with 6 outputs, 8 wires with alligator clips that can be used on 8 acupoints individually or at the same time to apply acupuncture needle treatment; and it is also equipped with 4 self-adhesive electrodes that can be used to apply electrical stimulation without using acupuncture needles. ISO 9001/2000 Certified. Size: 8.5”L x 6.5”W x 3.0”H, Weight: 3.3 lbs, Accessories include: 1 acupoint detecting probe, 8 wires with 8 alligator clips, 4 self-adhesive electrodes, 1 User’s Manual, 1 acupuncture meridians and acupoints chart, 1 A/C adaptor for both 110V & 220V worldwide use (can be used in America, Europe, South America and elsewhere).ITO ES-160 This is latest and most advanced unit in the line, it features 6 output channels and is manufactured in Japan. Compact, attractive, lightweight, sturdy and fits nicely on any desktop. Provides 8 stimulation modes and saves the settings from the last 5 sessions and incorporates 16 programmable memory settings. 3 LCD digital displays (0.6” x 1.4” and 0.6” x 1.1”) show point search sensitivity, frequency (Hz), pulse width (us), program modes, memory data, treatment time (minutes) and battery life. The hand probe includes a search to treat push button switch on the probe itself. Safety features include a self-test, zero start, automatic power off if its left unattended for 5 minutes and sound notice for power on/off. Also has an emergency stop button, hi/low voltage switch and it signals a tone to mark the end of a treatment. Accessories include search/ stimulation probe, 6 electrode cords, 12 alligator clip-on and an operation manual. Batteries are not included. E600 HAN Digital Electronic Acupunctoscope The E600 HAN Digital Electronic Acupunctoscope is an advanced multi-purpose 6-channel acupuncture stimulator with point detection capabilities. This device features 9 digital displays, which allow the user to easily view the settings for intensity, frequency, pulse width, and time of stimulation during operation, and make adjustments as needed. The E600 HAN supports 6 different waveforms, including the HAN waveform. Also included is a unique search-to-treat probe. This allows the practitioner to find an acupuncture point using the probe's point detection capabilities, and immediately stimulate the point by using its stimulation capabilities. You can be assured of your patient's wellbeing with the E600 HAN's built-in safety function. This immediately stops the power output when a function is changed during treatment. The device also gives you the option of using the included AC Adapter, which saves on batteries. Accessories include search-to-treat probe with grounding pole, 6 sets of TENS lead wires, 12 duck beak clips, AC adapter, and instructions. Specifications 500 ohm test load Output channels 6 channels (stimulates 12 points) Volts & current Low 0 to 5 volts, 0 to 10 mA (milliamp) High (H switch) 0 to 15 volts, 0 to 30 mA Pulse shape Symmetric biphasic square wave, square wave with negative spike (for HAN mode) Pulse width 50 to 400 µs, adjustable Pulse modes Continuous, Intermittent, Ripple, Dense & Disperse, Modulate, HAN mode Pulse rate 0.5, 0.7, 1 - 500 Hz adjustable Timer 0 to 60 minutes and Continuous Skin impedance monitoring LCD meter displays scale from 0 to 200 and sensitivity setting 3 levels: L5, L10, L20 with Sound On/Off function Power source 6 standard 1.5 volt C batteries (if using transformer, it should be 9V, 150mA), AC Adapter Size, Color, Weight 11.8" x 8.3" x 2.5", gray, 1.9 lbs.

All rights reserved. Copyright © 1998 - 2013  T & D Enterprises
disclaimer  privacy policy  FAQ